- How do I enable disk controller in BIOS Dell Optiplex?
- How do I enable AHCI in BIOS?
- How do I enable hard drive in Dell BIOS?
- What is UEFI boot mode?
- How do I get BIOS to recognize my hard drive?
- What do I do if my internal hard drive is not detected?
- How do I fix AHCI BIOS not installed?
- How do I enable AHCI without reinstalling Windows?
- What is AHCI mode in BIOS?
- What is SATA mode in BIOS?
- Where is SATA mode in BIOS?
- How do I manually add UEFI boot options?
How do I enable disk controller in BIOS Dell Optiplex?
WorkaroundEnter the BIOS by pressing F2 multiple timnes while the Dell Logo is shown.Navigate to Boot Sequence and set Boot List Option to UEFI.Navigate to SATA Operation and choose AHCI.In Advanced Boot Option you click on Enable Legacy Option ROMs.Set Secure Boot to Disable..
How do I enable AHCI in BIOS?
In UEFI or BIOS, find SATA settings to select the mode for memory devices. Switch them to AHCI, save settings and restart the computer. After the restart, Windows will start installation of SATA drivers, and when it is over, it will ask you for another restart. Do it, and AHCI mode in Windows will be enabled.
How do I enable hard drive in Dell BIOS?
Identifying the hard drive in the BIOSTurn on or restart your system.When the Dell logo appears, perform one of the following actions to enter the BIOS setup program: With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
What is UEFI boot mode?
Your system is equipped with UEFI BIOS, which is based on the Unified Extensible Firmware Interface (UEFI) specification. … For this reason, the system can be configured to boot in Legacy BIOS Boot Mode or UEFI Boot Mode. Legacy BIOS Boot Mode is the default.
How do I get BIOS to recognize my hard drive?
To check to see if this is the cause of the BIOS not detecting the hard drive, follow these steps:Power off the computer.Open the computer case and remove the data cable from the hard drive. This will stop any power saving commands from being sent.Turn on the system. Check to see if the hard drive is spinning.
What do I do if my internal hard drive is not detected?
Then the solutions should be quite clear in your mind: check connections, update device drivers, and enable the device in BIOS.Check the Connection Between the Hard Drive and the Computer. Connect your hard drive with SATA cable instead of USB cable. … Manually Update Hard Drive Driver. … Enable the New Hard Drive in BIOS.
How do I fix AHCI BIOS not installed?
Re: “No device found AHCI BIOS not installed” Please Help Type in the box regedit then click on the regedit. 6) Then just exit out of Regedit then restart the computer. 7) Then go into the BIOS configuration screens and change the disk mode to “AHCI”. Save the new BIOS configuration and restart so that Windows boots.
How do I enable AHCI without reinstalling Windows?
Enable AHCI Mode In Windows 7 Without ReinstallingLaunch the registry editor:Navigate to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\msahci.Set the Start value to 0 : Windows 7 msahci Start 0.Reboot your system.Go to UEFI/BIOS during the reboot and change IDE to AHCI.
What is AHCI mode in BIOS?
AHCI stands for Advance Host Controller Interface. It is a newer technology to provide advanced features to the Serial ATA standard. … If you do not feel comfortable installing AHCI drivers, you may use what is referring to as SATA IDE Compatibility Mode which can be triggered in the motherboard BIOS.
What is SATA mode in BIOS?
The SATA Mode BIOS feature is similar to the SATA Operation Mode BIOS feature, but with different options available. It controls the SATA controller’s operating mode. … When set to RAID, the SATA controller enables both its RAID and AHCI functions. You will be allowed to access the RAID setup utility at boot time.
Where is SATA mode in BIOS?
You can change how a SATA hard drive is configured in the computer’s basic input/output system (BIOS) setup.Restart or power on the computer. … Use the directional keys to select the “Main” or “Integrated Peripherals” menu. … Scroll to the “SATA Mode” option. … Press “F10” to save your changes and exit from the BIOS.
How do I manually add UEFI boot options?
Adding a boot option to the UEFI Boot Order listAttach media with a FAT16 or FAT32 partition on it.From the System Utilities screen, select System Configuration > BIOS/Platform Configuration (RBSU) > Boot Options > Advanced UEFI Boot Maintenance > Add Boot Option and press Enter.Browse for an .More items…